PDA

View Full Version : Wheelers add a leaf installation problem



Cedar Jones
10-23-2011, 08:14 PM
Hi, I'm installing some wheelers add a leafs on my 1999 Tacoma and I've run into a little problem. It seems like the leafs are too long because they are bumping up against the rear clamp holding the factory leafs together. I don't have them backwards. Has anyone run into this problem or am I just missing something obvious?

73768

73767

Falkon
10-23-2011, 11:11 PM
Doesn't this require a clamp to fit around all, the old and new leaves, to keep it together? I would think there would be a new clamp or a way to reuse the old clamp to incorporate the new leaf into the pack.

Never done this process or seen it, just my general understanding.

Good luck though!

Cedar Jones
10-23-2011, 11:22 PM
Thanks for the reply! As far as I can tell, the U-bolts that attach the axel to the springs are enough to keep the additional leaf in line. There isn't enough room in the clamps on the springs to fit an additional leaf and I haven't read anything in the instructions about needing a new, larger clamp. I'm going to call wheelers about it tomorrow when they are open, hopefully I'll be able to sort it out with them.

keezer37
10-23-2011, 11:26 PM
On my '05, the leafs sit solo. It doesn't get clamped. I'm wondering if they sent the wrong ones. The part number for the '05+ AAL is WHE ACH21. They didn't send you these by mistake, did they?

Cedar Jones
10-23-2011, 11:29 PM
That's the weird thing, the part number matches (it's WHE ACH30). It says it correctly on the invoice, and it's marked on the leafs as well.

Tim A
10-23-2011, 11:33 PM
This may be a stupid question: can you slide the clamp far enough backward that the AAL doesn't touch it? Also, does it matter if the AAL touches the existing clamp?

Cedar Jones
10-23-2011, 11:37 PM
I can't move it because it's bolted to the lowest factory leaf. I think it would matter if it touches the clamp, because it wouldn't be able to flex if it was running up against the clamp.

Zac808
10-24-2011, 07:43 PM
They sent you the wrong leaf. It should be shorter.

Cedar Jones
10-24-2011, 11:27 PM
Wheelers got back to me and they say it's a rare factory inconsistency. They recommended cutting off the rivet that holds the clamp around the factory leafs. Do any of you feel like that would be a bad idea? Seems like it's probably there for a reason... but on the other hand there's a clamp on the other end anyways, and with the U bolts holding the leafs as well, I guess it would be pretty hard for them to go anywhere.

Falkon
10-25-2011, 12:08 AM
In my opinion, I'd say no go to modifying the clamps. Have them send you a new set pdq, especially if they said it was their error.

keezer37
10-25-2011, 12:38 AM
If I understand you correctly, Wheeler's is saying your OE leaf clamps are incorrectly positioned from the factory. I'd verify this. Hopefully another '99 Tacoma owner here could chime in or hunt around your neighborhood with a measuring tape.

The clamps do keep the leafs from slipping out of line with each other horizontally. The u-bolts limit this, but as the springs flex, they will move. You do have the forward clamp though.

Are the clamps an equal distance from the centering pin? Is the hole in Wheeler's AAL centered? I'm thinking the AALs were drilled in the wrong spot.

Cedar Jones
10-25-2011, 01:41 AM
From what I understood they were saying that the leafs on my truck are differently positioned than the vast majority of 1999 4x4 SR5 Extended Cab Tacomas. The hole on the AAL is not centered. I asked Wheelers about drilling a new hole in the AAL and they said the steel is probably too hard for me to do this easily. I also measured the stock leafs and the bolt hole is 18 inches from the rear clamp and 16 inches from the front clamp. You're right, it would be super helpful if someone else with a 1999 Tacoma measured theirs to see if the clamps are in a different place.

washington taco
10-25-2011, 02:58 AM
I just cut down the Wheelers AAL and drilled a new hole for the teflon rub pad. I have a 2000 Taco and they were to long for mine as well. I would not remove the clamp.

Cedar Jones
10-25-2011, 03:34 AM
So you didn't have any problems cutting and drilling the steel?

Box Rocket
10-25-2011, 03:52 AM
Yep. I'd have them send you the correct leaves. Or if you decide to modify something instead, I shave a little off the end of the AAL before I messed with the clamp.

TACODOC
10-25-2011, 04:01 AM
I just cut down the Wheelers AAL and drilled a new hole for the teflon rub pad. I have a 2000 Taco and they were to long for mine as well. I would not remove the clamp.

Good advice

bat
10-25-2011, 01:29 PM
Try just trimming the pad and see how the leaf sits against the clamp.

DesertBoater
10-25-2011, 04:29 PM
I had the same exact problem when I added a leaf onto my '05 tacoma. I ended up removing the clamp instead of cutting the AAL...Big Mistake. From then on, my leaf springs squeaked at every little bump. The U bolts do hold them mostly in place, but they end up splaying out just a little bit and rubbing on the clamp at the forward end and squeaking. Both sides did it, not just one. I would see if they could send you a new set with a similar weight rating but a shorter length...

Cheers,
West

Cedar Jones
10-27-2011, 08:16 PM
I ended up cutting the leaf and leaving the clamp intact. Drilling the new holes was a pain, so I took it to Oregon Auto Spring and they drilled the new holes for $10, which was well worth it. The rest of the installation went great, now my truck is almost level with a small rise in the back, which is exactly what I wanted.

I guess people ordering AALs from wheelers should measure their leaf springs and ask wheelers to be sure they'll fit, because they don't fit every tacoma, even if you give them your year and model. Thanks for all your advice everybody!