Search:

Type: Posts; User: pods8

Page 1 of 20 1 2 3 4

Search: Search took 0.05 seconds.

  1. A friend has an 80s grandby that he added...

    A friend has an 80s grandby that he added brackets onto (don't know if his only has a single 1x1 in the corner or not off hand) and it holds. You mentioned fixing the broken welds already, does that...
  2. What are you trying to accomplish? If you're...

    What are you trying to accomplish? If you're using the jacks for the manner intended with this camper (ie on/off the truck evenly) it doesn't need an incredible about of beefing up. These aren't...
  3. Frames are generally the same from then till now...

    Frames are generally the same from then till now I think, you're only working with 1x tubing in the wall so keep that in mind when choosing bracket material/hole locations so you actually hit the...
  4. I have no idea what you have for a structure in...

    I have no idea what you have for a structure in there but assuming enough you can buy or make brackets. I made some for mine using angle similar to above but also a flat bar as well backed against...
  5. Thread: 4WheelResto

    by pods8
    Replies
    29
    Views
    1,598

    L-track.

    L-track.
  6. Thread: 4WheelResto

    by pods8
    Replies
    29
    Views
    1,598

    Very nice work.

    Very nice work.
  7. Wiser minds flagged that grey can actually heat...

    Wiser minds flagged that grey can actually heat up quite a bit (I knew it would get hotter but didn't realize how much), I masked off the grey with some white paper and shoved the front of the camper...
  8. Replies
    13
    Views
    978

    If you went with a flatbed build you have options...

    If you went with a flatbed build you have options but still snug. Go with the typical side entry door/rear dinette/front kitchen area. Have it laid out so the dinette is decently wide (maybe 48" if...
  9. Fixing these specific areas I'm not too...

    Fixing these specific areas I'm not too overwhelmed by (whether I did it from the front or back) the issue would be if its happening all over (or repeatedly).

    What is odd to me, though I haven't...
  10. Yes I know about the UV the areas in question are...

    Yes I know about the UV the areas in question are already painted (I pulled up an old post there of delamination from heat blankets prior to paint.

    I believe boats mostly use polyurethane foam...
  11. Replies
    13
    Views
    978

    Would a pop-up trailer work for you? More space,...

    Would a pop-up trailer work for you? More space, less cost, more flexibility on tow rig.

    3 of us use a standard grandby hunting and its snug, no way 4 would fit the normal layout. One option...
  12. A disheartening occurrence occurred. I'm...

    A disheartening occurrence occurred. I'm knocking out a kitchen table out in the garage for the wife and then was going to switch gears to completing the lower half shell. I had the door open on a...
  13. Cheapish insurance to buy 5 at the same time to...

    Cheapish insurance to buy 5 at the same time to have a spare in case you're in the boonies if one fails and also so your potentially needed future spare is as similar as possible (in terms of speed,...
  14. I have some firgelli 400# units that I wanted to...

    I have some firgelli 400# units that I wanted to sorta test their capacity (and how much the amp draw varied between unloaded and heavy), I don't recall the exact weight but I clipped myself in a...
  15. No idea what is on the market, I just know I'd...

    No idea what is on the market, I just know I'd look long/hard for them and know what kind of value they'd hold to me personally with hindsight. If I didn't need to spend the hours I needed to making...
  16. Find some panels, trust me. :p No its a few...

    Find some panels, trust me. :p

    No its a few inches higher than the stock bed (I want to say 3-4" off my head but don't recall the stock bed height anymore, I think it was earlier in the...
  17. Moving to a new place, had to make up the jack...

    Moving to a new place, had to make up the jack brackets. Got to see what this looked like on the truck, SOMEDAY...
    ...
  18. Been on an extendo break, reality of 3 little...

    Been on an extendo break, reality of 3 little kids set in once #3 cleared the mostly all sleeping stage (along with still trying to pursue some other things in life). Life is calming down again,...
  19. Replies
    212
    Views
    47,309

    So our new base slides and swivels? That's...

    So our new base slides and swivels? That's pretty cool if so.
  20. Replies
    192
    Views
    36,859

    Naw, I have you beat. :p

    Naw, I have you beat. :p
  21. Replies
    630
    Views
    221,512

    The relay board with a main bus is pretty cool of...

    The relay board with a main bus is pretty cool of dispersing power in the back yet having low amp switches elsewhere.
  22. I was looking around some on astro stuff and as...

    I was looking around some on astro stuff and as long as you were using stock stuff I didn't think it sounded too bad for anyone that is comfortable pulling the subframe out from under a vehicle. ...
  23. Replies
    60
    Views
    27,477

    Like I said predictable. ;) you have control...

    Like I said predictable. ;) you have control over temp to avoid. I have two speeds of epoxy hardener specifically to deal with high and low temps, know your product and when to use/not use.
  24. Replies
    60
    Views
    27,477

    Two part products are nice for predictable curing.

    Two part products are nice for predictable curing.
  25. Replies
    7
    Views
    741

    It's just two wires, a basic single pole switch...

    It's just two wires, a basic single pole switch is fine. I installed one in parallel to the thermostat on my old camper.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4