Search:

Where did the factory install it? Don't know where to start.

DK

Do any of you guys with the Habitat have satellite radio? My Sirius radio sucks now. I either have to move the antenna or get a new one. Just don't know where to put one...

Wade, Nice PICS! I am...

Yes. A foam pad that is covered in fabric. I don't think any of us are using it for the reasons mentioned above. Too narrow mostly.

Hey Mario/Martyn
I'm afraid I have another problem. Every time I turn a corner there is a piece of metal that is sliding back and forth in the front trough of the base section. It is right above the...

If the price is right, I want two. one for back and one for the side.

Yes, they took the tent completely off and then when they put it back on it now has the sealing strip under it. I am going to caulk the corners that have a gap. Don't know why they leave those...

Dan
The foam pad type system has two problems as I see it. There has to be a gap on the sides for the tent/poles to lay in. This leaves a big gap on each side and is a waste of sleeping space. You...

Subscribed.
I spent all morning cleaning the inside of my Jeep after AT got done with the "repairs" to the crappy texture job the painter did. They didn't take the top off to sand it down and that...

Very tight means the wind won't make as much noise. Mine is too.
Going back this week to get the texture mess fixed. Mario says he has the fix for the torsion rod so I can close it easier and a...

Are those events open to all comers? How would I find out about it?

Good for you Wade. I'll wait for warmer weather... I have some work to do on the steering and suspension. Too cold and no time to work on it.

Hey JRUEPPEL,
That is a NICE picture. AT should be hitting you up for cover art.
Just too cold for me.

The only way I can do it by myself is to stuff all the sides in and then climb up on the back and sit down to do the latches up. So far it has not gotten one bit less tension.

Mario,
When Brian came by the one thing that the tent itself is causing a small problem (for me in the desert small) is the flap on the back section. It is very short and the way my tent got...

I drilled a hole in the floor of the base section which came out right behind the driver side rear door very close to the edge. My "house" battery is mounted on that little shelf area behind the rear...

No, my box is shot. Death warble on hard braking. Putting in an aftermarket version with 1-3/4 hydraulic cylinder. AGR Performance.

Too bad you don't have two of them to put on at the same time. Then have Cam develop a triangle piece that goes between the two to form one continuous cover. Stick a support pole in the center of the...

Then it's going to take a little time to get all your stuff set up. I'm up for a test trip with you if you want. Let's do it in southern AZ though. The higher elevation over here is getting COLD...

Come through southern New Mexico and you cans spend the night in mine. BYOB - Bring your own Bag! I'll even park it in the warehouse so it's not so cold. Hit 28 last night.

I have the ARB dual motor compressor installed in the cubby in back. I built about a 3 gal tank out of a piece of pipe and put it between the gas tank and the rear axle. I then ran 1/2" air line to...

Took mine out for an overnighter in the desert. Didn't take a single picture. I took out the double air mattress and put in my tried and true Big Agnus bag and air mattress. Better than sheets and...

Speaking of which, I expected to see something by now. Mario, what's up with the awning?

OK. New Topic. Bugs.
As posted above, I was out a couple of weeks ago for two nights. There were some miller bugs flying around, not too many. They ended up in the tent. The main way they got in was...

I have two 25" air mattresses side by side in the Habitat. They just barely fit, so I would say it is at most 50" wide. The front and rear are about the same width. I think it is the same as a double...

Hey Dan,
1) I took out the foam pad. I bought two Nemo insulated Cosmo air mattresses with the double pillow top. The good thing is it completely fills the width of the shell, each pad being 25"...