HazVan - 2002 E-350 SuperDuty 7.3l PSD

Bikersmurf

Expedition Leader
Your rigs weight distribution is likely different than mine. In mine, I’d be most concerned about rear traction. It’s got 6000 lbs over the rear axle. Experience has shown that both rear wheels will stay on the ground and front wheels will be airborne quickly. Thus making open diffs and LSD less useful. I’d not want a locker that I can’t control there because I find open diffs steer better in the snow & ice.

I’ve had an Fj40 for 29 years now. In ‘92 I rebuilt the rear tub with 1/8” steel steel. The relevance being, it now weighs 2000lbs in the front and 2500 lbs rear. It’ll go almost anywhere with both diffs open. Most places it’ll pass other 4x4s in 2wd. On snow and ice it steers well (at reasonable speeds) so long as I’m delicate on the throttle. Once both front wheels are spinning, turning steering is less productive. With an open front diff, one wheel isn’t spinning, it’s the wheel with the best grip and thereby I’ve got something to steer with.

My first choice would be LSD in the rear, and open in the front, If you’ll be doing more serious wheeling, locker in the rear and selectable in the front,

that said, I’ve not got your rig, nor do I know where you plan to drive. So do what makes sense for your situation.
 

turbodiesel

Active member
Your rigs weight distribution is likely different than mine. In mine, I’d be most concerned about rear traction. It’s got 6000 lbs over the rear axle. Experience has shown that both rear wheels will stay on the ground and front wheels will be airborne quickly. Thus making open diffs and LSD less useful. I’d not want a locker that I can’t control there because I find open diffs steer better in the snow & ice.

My first choice would be LSD in the rear, and open in the front, If you’ll be doing more serious wheeling, locker in the rear and selectable in the front,

that said, I’ve not got your rig, nor do I know where you plan to drive. So do what makes sense for your situation.
Thanks for the thoughts. I've concluded to go with Open front / LSD in rear. Not doing any serious wheeling, mostly 4wd for mud/snow/ice in the Sierras on the west coast USA.
 

Bikersmurf

Expedition Leader
Love the new roof btw. If I could get my hands on one I’d like to modify the front edge do it was straight and then mount it atop my type three.

While I’m in this fantasy world I’d punch a smaller hole to access it through and have a bed permanently set up there... and then tour the continent kith my kids before they are to old to be seen with their Parrents.
 

turbodiesel

Active member
Inside has changed a bit since I last posted what it looked like. Also welded up a cargo carrier for above the aluminess box. Mostly as a cheap way to mount ski racks on the back. Buying the steel to make my own was more expensive than buying a harbor freight one and customizing to my needs. Economy of scale I guess... Removable cross pieces at not pictured, paint is drying.
 

Attachments

  • PXL_20210101_235219565.jpg
    PXL_20210101_235219565.jpg
    1.7 MB · Views: 45
  • PXL_20210102_005245896.jpg
    PXL_20210102_005245896.jpg
    1.5 MB · Views: 49
  • PXL_20210102_005259487.jpg
    PXL_20210102_005259487.jpg
    1.6 MB · Views: 50
  • PXL_20210102_005745086.jpg
    PXL_20210102_005745086.jpg
    1.5 MB · Views: 49

Bikersmurf

Expedition Leader
Swapped out the transmission cooler for a trucool cooler. Fairly quick, took about two hours. I have the bypass as well but haven't installed it yet.
6cd464ecbbea393bd96cf7e7aba59011.jpg
80894b1838bdfa02861b200b332b034a.jpg
96ca1992af6f476bf9e2ca97028a9332.jpg
I’ve been looking at a couple of different TruCool options. Which on did you go with?
 

turbodiesel

Active member
I’ve been looking at a couple of different TruCool options. Which on did you go with?
Tru-Cool Max LPD4739 4739 40,000 GVW Low Pressure Drop Transmission Oil Cooler with Thermal Bypass

It's very good. I need to install the bypass as the temp rarely exceeds 150 in non mountain grade driving. I suspect in winter conditions it'll be necessary to get the transmission up to temp.
 

turbodiesel

Active member
@turbodiesel Maybe I missed it in your build but what's the bench seat from? Happy with it?
Ford Transit 15-19 31" 2 person seat new take out. Bought it of eBay for $300 with mounting rails. I'm extremely happy with it. It's easy enough to remove and installation wasn't bad. I added aluminum plates underneath to reinforce the mounting points. It also has headrests but I remove them unless someone is sitting there; that allows me to see out the back.

I needed 31" to fit my van but it's a little small with two adults for a long road trip. For eating at the table it's fine though. Kids have no issues.
 

iggi

Ian
Ford Transit 15-19 31" 2 person seat new take out. Bought it of eBay for $300 with mounting rails. I'm extremely happy with it. It's easy enough to remove and installation wasn't bad. I added aluminum plates underneath to reinforce the mounting points. It also has headrests but I remove them unless someone is sitting there; that allows me to see out the back.

I needed 31" to fit my van but it's a little small with two adults for a long road trip. For eating at the table it's fine though. Kids have no issues.

Thanks!
 

Bikersmurf

Expedition Leader
Tru-Cool Max LPD4739 4739 40,000 GVW Low Pressure Drop Transmission Oil Cooler with Thermal Bypass

It's very good. I need to install the bypass as the temp rarely exceeds 150 in non mountain grade driving. I suspect in winter conditions it'll be necessary to get the transmission up to temp.
Sounds like the one I saw. I wondered if the Bypass was necessary... but based on your numbers it sounds beneficial. I’m sure my stock one leaves something to be desired (9k+ rig empty, 8.5’ tall, 7.5’ wide).
 

turbodiesel

Active member
Sounds like the one I saw. I wondered if the Bypass was necessary... but based on your numbers it sounds beneficial. I’m sure my stock one leaves something to be desired (9k+ rig empty, 8.5’ tall, 7.5’ wide).
I'd suggest installing without it and then testing. It shouldn't be too much effort to cut the line and put in the by-pass. I was waiting on my winter trips to make the final call. Those didn't happen with Covid, so I haven't added it yet.

I think in winter it might be needed. Depending on who you ask/read 150/160/170 is the ideal temp. In my view if it's between 140-180 that's a'ok.
 

turbodiesel

Active member
Started tearing down the axle to regear the front axle from 3.73 to Yukon 4.30.

Bearing removal was a huge problem with removing the external snap ring. Try cheap ring pliers, they broke. Channel lock brand snap ring pliers set, while very nice, was too bulky. Returned. If you have to remove the wheel bearing on a 2005+ F250/350 axle, the tool for the job is KNIPEX https://www.amazon.com/dp/B0002YYMDK/

Trust me, with that it took less than 30 seconds to remove both.

Axle removal was brute force. Get a large pry bar, I used a 36" Estwing, and pry side to side until it just pops loose. Took longer than I thought it would but just keep at it.

Knuckle removal is optional, but the ball joints were pretty worn and needed to be replaced.

Finally was able to remove the diff after draining the rest of the gear oil. It was surprisingly easy. Take large pry bar, stick it behind the diff and between the housing and leverage. Out the diff came.

Next up is the tedious part of preloads and bearing replacements.
469e41582d403921f5b1d0c27d5201a9.jpg
e3b1767befc2b2fdd938b6fbb5ae74d2.jpg
bdd05c7abf3b1872642a7f8e28c6df29.jpg
89c0480ef5982188a77068b69ff9d64b.jpg
63f72236858ebf2539b642c997f48299.jpg
 
Last edited:

turbodiesel

Active member
Installed the spring perch and bolted it down. One thing to note is the shock point for the spring perch needs the Ford 24-06213-32369 nut with the little arm. I originally tried putting a 3/4" nut on there and realized no wrench would fit in there. Definitely a couple minutes of confusion. It's also supposed to use Ford W500765-S439 bolt, but as I was prepping I checked my spreadsheet and they never arrived. I used the McMaster grade 10 bolts in it's place.

Sanded and gave the axle a first coat of paint. Not looking for show room quality here, just clean off surface rust and paint it to help keep it from coming back.

Got the pinion and seals out. Working on the bearing chase. Then it'll be on to test fitting the new gear.

708d89f0b2a44f947d4d74b95e65f268.jpg


ce467009f668597223e3f27a0f406513.jpg


6c87faa8af7a6eb6c003c6416153bdb3.jpg
3cc541722b33815ad95921c331b7f46f.jpg
c7efefb7e41fcb8e924d0879a40a7c29.jpg
 
Last edited:

turbodiesel

Active member
Already made a mistake in not looking at my spreadsheet on install order. Radius arms need to be installed on the axle before the MG Shock/Spring mounts.

Lower spring mounting orientation diagram
 

Attachments

  • user6701_pic40144_1552152103.jpeg
    user6701_pic40144_1552152103.jpeg
    82.7 KB · Views: 19
Last edited:

Forum statistics

Threads
185,534
Messages
2,875,626
Members
224,922
Latest member
Randy Towles
Top