Recent content by Bris31

  1. Bris31

    suspension suggestions

    Camper looks nice on SWB shorty. But just curious about camper door location on driver side in US.
  2. Bris31

    new owner of Fuso

    Congratulations! Planning is half the fun. Good luck.
  3. Bris31

    (FIXED) Canter FG649 (2003) clutch pedal is free

    FIXED (fingers crossed): After a tip from a panel beater- opened 2 main bolts to the bracket and removed the in/out pipe. Then loosened the 'push rod' with a pliers jammed on the grooves which are just behind the locknut (it found to be too tight). I was told these grooves are meant for this...
  4. Bris31

    (FIXED) Canter FG649 (2003) clutch pedal is free

    New master cylinder coming next week. Yes, I intend to have same old measurements of push rod length etc on the new master. Maybe cutting a small window on the front panel will help with installation for my big hands? ;) It looks so simple but needs lots of patience and reach. Wonder how do...
  5. Bris31

    (FIXED) Canter FG649 (2003) clutch pedal is free

    Just a thought, if rubber seal is buggered, shouldn't be oil would be leaking out all over?
  6. Bris31

    (FIXED) Canter FG649 (2003) clutch pedal is free

    Great, I could check master cylinder rod moving when clutch pedal is pressed - without removing master cylinder. So looks like seal is at fault as Dan mentioned. Will get a new master cylinder to replace.
  7. Bris31

    (FIXED) Canter FG649 (2003) clutch pedal is free

    Dan, thanks for quick reply and tip about removing the air lock. Would it be much easier to change the CLUTCH MASTER CYLINDER ASSY, than repairing the rubber seal? The whole thing cost only $116 at Brett. Also I was thinking before removing the master cylinder, I remove the clevis pin from...
  8. Bris31

    (FIXED) Canter FG649 (2003) clutch pedal is free

    This morning after a week of truck sitting idle, started the truck and found clutch pedal is free i.e. it goes to floor freely and doesn't return. Did some basic troubleshooting:- Found no oil leakage anywhere - inside cabin or on ground below. Brake oil level is same as before this problem and...
  9. Bris31

    FG's in Action

    10 days ago completed 16K km (10K miles) lap around Oz - mainly an offroad 3 months trip. One of the highlight was an incident happened after left front shock failed - bottom eye broke and came out of socket. After heavy rain the previous night, as I was trying to negotiate a puddle on a...
  10. Bris31

    FG's in Action

    I have to remind myself opposite driving on sandy hills (e.g. in Fraser Island) where downhill traffic has the right of way ;)
  11. Bris31

    FG's in Action

    Fuso company would love to see. Anyway nice video editing from number of cameras (4 at least).
  12. Bris31

    Availability of 16" Alloy Wheel 5 stud 1800kg load rating for 315/75R16 tyres

    Anyone knows where these rims can be sourced in Australia or abroad? (Melb outback shop doesn't have atm) Need for 2nd spare - new or used. Thanks in advance
  13. Bris31

    16" Alloy Rim 5 stud for Canter pre 2007 models.

    Need one 16" alloy rim new or used as shown in photo. Rating 1800kg It is for Mitsubishi Canter FG649 pre-2007 models
  14. Bris31

    FG's in Action

    From May to August with friends (3 Canters and a Isuzu) did about 16,500km lap from Australia's eastern coast to western coast mostly through back tracks. One of the highlight was Gunbarrel track. More photos: http://foxroo.com/travel/show.asp?g=Gunbarrel%20Highway&r=1
  15. Bris31

    Need part number for AC condenser FG649 2003

    Anyone have part number for AC condenser FG649 2003? I think it should be same for FG649 2002-2007. I got AC condenser front end crooked from hits from recent 3 months offroad lap around Australia. Seems new one cost about $895+gst Also if someone have replaced one with after market or about...
Top