Recent content by micoinde

  1. M

    M101A2 Leaf Spring Replacement

    Where may I purchase replacement leaf springs for my M101A2 near or in the Delaware area? I discovered the right-side leaf spring to be sagging.
  2. M

    M101A2 build

    Finally installed the ARB 2500 awning with Frontrunner Quick Release. Added the MaxiTrac 8x8 vehicle awning to the Tundra. The awning is not as “stout” as the ARB 2500 on my trailer but for $99 from NAPA, we’ll give it a try. I mounted to the bed racks with the Frontrunner Quick Release...
  3. M

    Question to those running the same vehicle wheels on your trailer..

    Do it. 2007 Toyota Tundra 1991 M101A2 with Dexter 3500 axle swap Sent from my iPhone using Tapatalk
  4. M

    M101A2 build

    Finally finished the axle and wheel swap. Dexter 3500 Carry-On Trailer 10 inch drum hubs / Brakes MotorSport Tech, Reno NV wheel adapters Sent from my iPhone using Tapatalk
  5. M

    Adventure Brick

    Where did you get the exterior mountain image decal?
  6. M

    M101A2 build

    Built storage boxes with removable tops around the DECKED system. Done! Sent from my iPhone using Tapatalk
  7. M

    M101A2 build

    $50 bucks and an hour of sweat equity resulted in a sleeping platform with storage. Sent from my iPhone using Tapatalk
  8. M

    M101A2 build

    Picked up a used short bed DECKED storage box for $50. I will make it work!!! Sent from my iPhone using Tapatalk
  9. M

    M100 aftermarket axle for Toyota bolt pattern

    As with the OP, I want the same wheels for both my Tundra and trailer. Do they make a 5 x 4.5 inch bolt pattern to 5 x 150mm Toyota Hub Centric wheel adapter? There seem to be many options for putting after market wheels on Toyota hubs but I can't seem to locate an adapter to put Toyota...
  10. M

    M101A2 build

    I'm about to delve into my axle swap and as always, put the cart before the horse. I got a Dexter 3500 64 inch and a pair of 10 inch drums for electric and parking brake with a 5 x 4.5 bolt pattern. I want to mount a pair of Toyota Tundra TRD alloy wheels which are 5 x 150 and HUB CENTRIC...
  11. M

    M101A2 build

    Rust-Oleum Universal Satin Black Spray Paint and Primer In One from The Home Depot. Sent from my iPhone using Tapatalk
  12. M

    Tongue Box Ideas for 1/4 Ton Military Trailers

    I secured a 2 inch 3/16 thick angle iron frame and dropped in aluminum tool chest. This box houses one Yellow Top, solar controller, NOCO Charger and stuff. Sent from my iPhone using Tapatalk
  13. M

    M101A2 build

    Replaced the smaller Harbor Freight tongue tool box with a larger aluminum Better Built chest. The steel 2 inch angle base frame was my first venture into welding. Chest will hold marine batteries, Noco Charger, solar controller, & stuff. Sent from my iPhone using Tapatalk
  14. M

    Dstock's M101A1 build... or the reality, I needed a new project!

    Good stuff. Are you planning on insulating for comfort? I need some ideas for my build. https://www.expeditionportal.com/forum/threads/m101a2-build.203188/
  15. M

    M101A2 build

    The rear receiver is 2 inch receiver tubing pushed through square cut in rear cross member and welded to inner frame cross member. The extension is used to push another 2 inch receiver sleeve out enough to use sky chair mount when tailgate is down. Sent from my iPhone using Tapatalk
See more
Top